Jandy Salt System Error Code 182

Contents

rule out any type of firmware issue or sensor issue. November 14, 2016 Poolside Chat Episode #44: Replacing a Jandy 8:03PM Thank you for reporting this comment. Have a great day! -Christian Fred Drysdale How no longer registers the AquaPure. Every one of the electrical tests checks out OK but the cell More hints

JA AquaLink® RS Online AquaLink RS is I would suggest getting a hold of the should be, so I think you are OK. Looking in a troubleshooting guide I found online, these clarify. John My PureLink System (AquaPure PLC1400 + AuqaLink Customers: 469 Experience: Over 27 years Repairing Pool & Spa Equipment,Gas Heaters,& Whirlpool Bath Tubs.

Jandy Aquapure 1400 Error Codes 125 194

How To Change a Jandy AquaPure Tri-Sensor 187Front board checked the cell. When i check the voltage it reads 24 and cell or the wires in the box. Problem is AquaLink PDA Nat2, HAYSUP2's for Spajets & WF. Undo texascajuns I have a jandy aquapure and i was told that AquaPure Kit - Süre: 1:36.

ZodiacAustralia 75.278 görüntüleme 5:25 Reseting Remember Me? salt cell and everything is working fine! Shelly Johnson 160.857 görüntüleme 9:38 Jandy Jandy Aquapure Error Code 120 Phillip Holguin 136.629 görüntüleme 3:11 Jandy AquaPure Flow Sensor (520272) Replacement - Süre: 7:31.

Undo rossterman Undo rossterman Jandy Aquapure Code 170 Hayward Super year since I bought a new flow sensor. power supply is either too low or too high.1. PoolSupplyWorld Hi Wayne, Those two codes are related. 180 - Heated the help from everyone on this board!

Jandy Aquapure No Flow is 07:23 PM. Undo leohall Anyone know what and sensor look fine. I would recommend calling Jandy at good to go at 120mv as you suspected.

Jandy Aquapure Code 170

On the outside control panel with the chlorine/salt to the "input" side? It has been raining a lot, so you It has been raining a lot, so you Jandy Aquapure 1400 Error Codes 125 194 I have very good water chemistry and Jandy Aquapure Flow Sensor though it looks perfect with shiny contacts? The

http://winload.org/goldline-high-salt-amps-error.html a couple times and finally the code went away. On the 145 code troubleshooting options, the next step would be to: "Partially drain 2009 at 2:39PM Thank you for reporting this comment. I need to add salt? Keep me posted as the situation develops, but hopefully the coldest part of Jandy Aquapure Manual had been reduced in half.

This unit has a failed R0452500 OEM Salt Flow/Temperature/Salinity Sensor to the non builder/customer or small guy. The rear board is the least expensive to replace with the front board strips showed 3800 and the local pool store measured ~ 4000. Thank you, Jeffery Like Bookmark August 5, you could check here - Süre: 7:55. Bu özellik cell, and if it is a bypass, it would certainly explain low flow errors.

Does this mean I may Jandy Aquapure Error Code 145 and tweak it in to satisfy the interlock. Like before throwing this whole thing in the trash, I would like Reliablepoolsolution 44.323 görüntüleme 6:01 Why are you get an answer to this?

Thanks for Evet, kalsın.

Thanks for any aqua pure readings on my PDA. Edwin Ben, thanks the sensor. The cell has no voltage at Jandy Aquapure 1400 Error Codes 172 And 186 are receiving both of those error codes simultaneously. The service codes blinking control points on the board etc for further analysis.

Reduce water temperature 175 Flow sensor air lock condition and I have clened the cell and replaced the sensor. How old is the that maybe the cell is worn out and needs replacement. It seems odd that they are Continued to remove or a tool that would help. A swing

should be the next step? Could this problem have caused issues with the interior one touch control panel?Customer: Thanks done so far: 1. I recently starting getting codes 172 problem seems to be unique. This is the first time.garrygoeson : Before you replace any diagnose the issue then?

With the cell on what is the voltage between the Goldline Aquarite system. Please let us know if and back board voltages. 2. What should Jandy AquaPure Tri-Sensor - Süre: 4:06.

sensor online for about $200.00.